10 Wood Stove Accessories: A Guide for Drolet & Englander Owners

Updated August 2026

The right wood stove accessories can support heat distribution, floor and wall protection, venting, combustion-air supply and everyday convenience. However, accessory compatibility and installation requirements vary by stove model, home and venting system.

This guide compares ten accessories commonly used with Drolet and Englander wood stoves. Before purchasing or installing any component, confirm that it is approved for your appliance and follow the product instructions, stove manual and applicable local building codes.

For help planning your complete wood-heating system, visit our Wood Stove Buying Guide.

#10 – Black Heat Shield (Optimized Packaging)

This freestanding heat shield helps protect nearby walls and objects from excessive heat produced by a wood stove. Its three-panel design provides coverage behind and beside the appliance, and no assembly is required.

This model is intended for added heat protection—not for reducing the stove’s required clearances. Position it according to the product instructions and always maintain the clearances specified by the stove manufacturer and applicable local codes.

Placement: This is a freestanding heat shield that requires no assembly. Position it according to the product instructions while maintaining all clearances required by the stove manufacturer and local codes.

#9 – Rigid Fire Screen

A rigid fire screen is a model-specific accessory intended for open-door viewing only when the stove manufacturer explicitly allows that operating mode. It can help contain larger sparks while providing a clearer view of the fire, but it does not eliminate the risk of escaping sparks or smoke.

Confirm that the screen is approved for your exact stove model, follow the appliance manual and never leave an open-door fire unattended.

#8 – 6" To-the-Wall" Double-Wall Pipe Kit

This connector-pipe kit is designed to connect a wood stove’s 6-inch flue outlet to an approved chimney system at the wall. Its telescoping sections and two 45-degree elbows provide flexibility when aligning the stove with the chimney connection.

In the box: 6" stove connector, 28"–50" telescoping section, 6" straight length, 12" straight length, two 45° elbows, wall-finishing band, 36 self-tapping screws.

This kit connects a wood stove’s 6-inch flue outlet to an approved chimney system at the wall. Its telescoping sections and two 45-degree elbows help align the connector without cutting fixed pipe sections.

Benefits: Double-wall construction helps maintain flue temperature and may allow reduced clearances compared with single-wall connector pipe. Required clearances depend on the listed system and installation instructions.

Important: Double-wall connector pipe remains inside the room and must not pass through a wall or other combustible partition. A wall penetration requires a listed wall thimble, insulated chimney components and the other parts specified by the chimney manufacturer. Confirm compatibility and required clearances before installation.

#7 – 41 ¼" × 44" Black Steel Hearth Pad

This 16-gauge steel hearth pad protects combustible flooring from hot embers that may fall while loading or operating the stove. Its low-profile, powder-coated surface provides durable ember protection and is recommended for stoves no larger than 26 inches deep by 20 inches wide.

Important: This hearth pad is intended for stoves that do not require a specified thermal R-value. If your stove manual requires insulated floor protection, choose a hearth pad that meets or exceeds that requirement. Always confirm the required dimensions and floor-protection rating before purchasing.

For more guidance on hearth protection, required clearances and safe operation, read our Wood Stove Safety Guide.

#6 – 5" Ø × 4' Insulated Flex Pipe (Fresh-Air Intake)

This insulated flexible pipe connects to a compatible 5-inch adapter as part of a fresh-air intake system. It uses reinforced aluminized trilaminate construction with fiberglass insulation and is compatible with select Drolet appliances.

Important: This pipe is only one component of a complete fresh-air intake system. Confirm the required adapter, exterior termination and compatibility with your exact stove model before purchasing. An outside-air connection should not be treated as a guaranteed fix for persistent smoke or draft problems.

#5 – Fresh Air Intake Kit

A fresh-air intake kit provides a dedicated path for outside combustion air on compatible wood stoves. It may be required for certain mobile-home installations or recommended where the appliance manual and installation conditions call for outside air.

Compatibility is model-specific. Confirm the correct intake kit, adapter, insulated pipe and exterior termination for your stove. Outside air may help in some negative-pressure situations, but it does not guarantee improved efficiency or resolve every startup-smoke or draft problem.

#4 – 25-Foot Stainless Flex Liner Kit for Inserts – 6" Flue

Designed to connect a compatible wood stove insert to a properly inspected masonry chimney, this 6-inch stainless steel flex liner creates a continuous venting path through the existing chimney. The kit includes a 25-foot liner, connector and rain cap.

Installation requirements vary by fireplace and chimney. Confirm whether insulation, adapters or other components are required, and follow the insert manual, liner instructions and local building codes. Professional installation and a chimney inspection are recommended.

Learn more about chimney liners, venting types and installation planning in our Wood Stove Chimney Guide.

#3 – 6" To-the-Ceiling Double Wall Pipe Kit

Designed for straight-up installations, this double-wall connector pipe kit runs from a compatible stove’s 6-inch flue collar to the ceiling support box. The double-wall construction helps maintain warmer flue gases and may allow reduced clearances compared with single-wall connector pipe when installed according to the manufacturer’s instructions.

Connector pipe must never pass through a ceiling or roof. At the ceiling support box, the venting system must transition to an approved insulated chimney system. Confirm stove and chimney compatibility, required clearances and all necessary components before installation.

Planning a new stove and chimney system? Review our How to Install a Wood Stove guide for clearance, floor-protection and venting considerations.

#2 – Thermodisc Kit

A thermodisc adds automatic temperature-based control to a compatible wood stove blower. It starts the blower after the stove warms up and turns it off as the stove cools, reducing the need to operate the blower manually.

Thermodisc and blower compatibility varies by stove model. Confirm the required part number in your stove’s manual and follow the supplied installation instructions before purchasing.

#1 – Blower Assembly with Variable Speed Control

A variable-speed blower helps circulate heated air from around the stove into the room, providing more even heat distribution. The adjustable speed control lets you balance airflow and noise based on your comfort preferences.

This blower does not increase the stove’s rated heat output, and it is not universally compatible with every Drolet or Englander stove. Verify the correct blower model in your stove’s manual before purchasing.

How to Choose the Right Accessories

Frequently Asked Questions

Do I need both the blower and the thermodisc? No. A compatible blower can be operated manually without a thermodisc. Adding a compatible thermodisc allows the blower to start automatically as the stove warms and shut off as it cools. Check your stove manual to confirm the correct blower and thermodisc models.

Can I install these myself? Some model-specific accessories, such as approved blowers or thermodiscs, may be suitable for homeowner installation when the manufacturer’s instructions are followed. Venting, chimney liners, outside-air systems and hearth protection may require permits, inspections or professional installation. Always follow the stove and accessory manuals and check local building-code requirements.

Are these accessories compatible with other brands? Compatibility varies by accessory and stove model. A shared measurement, such as a 6-inch flue diameter, does not guarantee that a component is approved for a particular stove or venting system. Check the appliance manual, accessory specifications and model or part number before purchasing. Contact FYRE Direct if you need help confirming compatibility.

Final Thoughts

The right accessories can make a wood stove easier to operate, improve heat circulation and support a properly planned installation. However, every accessory should be selected for your specific stove model and home—not simply by brand or pipe diameter.

Before ordering, review your stove manual and confirm the required part number, dimensions and installation requirements. If you are unsure which accessory fits your Drolet or Englander stove, contact the FYRE Direct team for compatibility assistance.

Once your system is installed, follow our Wood Stove Maintenance Guide to keep the stove, blower and venting components clean and operating properly.

Shop now — all products above are linked directly. Ready to upgrade your wood stove setup for the season?

Related Guides

This post is part of our complete Wood Stove Buying Guide. Explore more:

• How to Install a Wood Stove
• Wood Stove Maintenance Guide
  
• Wood Stove Chimney Guide